Certified to the heat
Mill test reports, chemical analysis and tensile data issued per lot — not per shipment, not per year.
01EN 13601 · ASTM B187 · ISO 9001 · DFARS
Copper stock, cut to size, out the same week.
Bar, busbar, tube, sheet, coil, wire and extruded profile — held in depth across copper, copper nickel, brass and bronze. Mill-certified to the heat, sawn and machined to your drawing, released against your lot number.
- Stock lines
- held
- Quote turnaround
- hrs
- On-time delivery
- %
- Supplying since
EN 13601
ASTM B187
ISO 9001:2015
DFARS 252.225-7014
RoHS 3
Mill certs with every lot
EEMUA 144
Buy American eligible
Welding & metal stock
Four ranges, 43 lines held in depth.
Pick a range to see everything in it, with the grades, sizes and certification for each line — or send a drawing and we will identify what you need and quote it.
16 lines
Welding consumables
TIG and gas rods, spooled MIG wire, coated electrodes and brazing alloys.
Silicon Bronze TIG Rod, Deoxidised Copper Rod, Aluminium Bronze Rod…
Browse welding consumables
6 lines
Cutting & torch gear
Gouging carbons, cutting nozzles, plasma consumables, torches and clamps.
Gouging Carbon Electrodes, Oxy-Fuel Cutting Nozzles, Plasma Cutting Consumables…
Browse cutting & torch gear
16 lines
Copper stock
Bar, busbar, tube, pipe, sheet, plate and extruded section.
Copper Round Bar, Copper Square Bar, Copper Flat Bar & Busbar…
Browse copper stock
5 lines
Alloy & specialist
Copper nickel for marine service, plus stainless bar and tube.
Copper Nickel 90/10 Tube, Copper Nickel 70/30 Tube, Copper Nickel Pipe Fittings…
Browse alloy & specialist
Cannot see what you need? Tell us the spec — we source outside the standing range daily.
Why buyers consolidate here
Built for procurement, not retail.
Every line item ships against a reserved heat lot with documentation attached before the material leaves the floor.
Delivery that lands
Own transport plus dedicated pallet and flatbed lanes from three regional yards. Banded and moisture-barriered.
02Cut and processed to size
Sawing, shearing, punching, drilling, bending and tinning in-house — so it arrives ready to fit.
03Four-hour quoting
Send a drawing, a spec callout or a part number. A materials engineer answers — same day.
04Documentation
The paperwork ships with the metal.
Receiving inspection should take minutes. Every lot arrives with its full document package barcoded to the outer wrap, plus a duplicate set emailed on dispatch.
01
Mill Test Report
Heat number, full chemistry, mechanical properties.
02
Certificate of Conformance
Signed against your PO revision and spec callout.
03
Country of origin & DFARS
Melt and manufacture location stated in writing.
04
SDS & RoHS 3
Current revision, no exemption claims.
How an order runs
Spec to dock in four moves.
-
01
Send the requirement
A drawing, an alloy designation, a competitor part number or a photo of the offcut. Any of it is enough to start.
-
02
Engineered quote in 4 hours
A materials engineer confirms grade, temper and tolerance — then prices it against live stock.
-
03
Lot reserved, material cut
Your heat is pulled, tagged and sawn to size. Mill cert, CoC and origin statement are raised against your PO revision.
-
04
Palletized and dispatched
Banded, moisture-barriered, barcoded. Tracking and the scanned document set land in your inbox at dispatch.
tCopper alloy on the floor
yardsRegional distribution points
+Accounts supplied
subsUnauthorised substitutions, ever
From the floor
Buyers who stopped shopping around.
We were losing two days a month chasing mill certs. Buy Hub Weld attaches them to the wrap. Goods-in inspection went from an afternoon to eleven minutes.
They spotted that drawn C101 would hold tolerance where our old supplier kept sending cast. Nobody else asked what we were machining.
Eleven pallets of busbar a quarter on a blanket PO, drilled to our centres, never a short ship. That is the entire review.
Questions from procurement
Answered plainly.
Anything not covered here, a materials engineer will answer by phone in one call.
There is no minimum on cut lengths from stock — we will sell you a single 300 mm offcut. Mill-run and non-stock sizes carry a minimum that we state on the quote before you commit.
Conversion cost plus the LME copper settlement averaged over the prior five sessions, restated Mondays at 09:00. The formula is printed on every quote, so you can audit it against the exchange yourself.
Yes, above roughly five tonnes annual usage. We place the stock, you draw against it, and we invoice monthly on consumption with a cycle count each quarter.
For most classes, yes. Melt and manufacture origin is stated on the certificate of conformance. Flag the requirement on the RFQ and we will only quote compliant heats.
Three to five weeks for a mill run, depending on alloy and section. We will usually propose a stocked adjacent size with the machining allowance worked out, so you can decide whether waiting is worth it.
Uncut, undamaged stock items return within 90 days at full credit less carriage. Mill-run and cut-to-length items are non-returnable, and we say so on the quote before you release it.
Request a bulk quote
Send the spec. Get real numbers in four hours.
Business hours, 07:00–18:00. Include the grade or just the application — either works. We will tell you if a cheaper alloy does the same job.
Answered by a materials engineer, not a call centre
No account setup required to receive pricing
Sample document set on request